ΑΝΑΠΤΥΞΙΑΚΟ ΜΕ ΜΙΚΡΟΕΠΕΞΕΡΓΑΣΤΗ PIC32MX220F032D LIKE ARDUINO UNO

12,48 € tax incl.

In stock / Delivery 1-3 Days

Quantity

More info
Data sheet

More info

ARDUINO-UNO like board with PIC32MX220F032D.

Generally this board outperforms ARDUINO-UNO in regard to hardware capabilities as you can see from the table below:

	PIC32-PINGUINO-MX220	ARDUINO-UNO
CPU	32 bit	8 bit
CLOCK	40 MHz	20 MHz
FLASH	32 KB	32 KB
RAM	8 KB	1 KB
USB	YES	NO*
LOW PWR	YES**	NO
GPIO MAX	40 MHz	5 MHz
ADC	1.1 MSPS	15 KSPS
DMA	YES 4 CH	NO
UEXT	YES	NO

* require additional chip FT232 or ATMega with USB
** hardware allows power down to 10 uA operation for hand-held battery apps

The only Pinguino shortcoming compared with Arduino is the smaller community and the less projects available ready for use.

FEATURES

PIC32MX220F032D 32 bit, 40 Mhz microcontroller 32KB Flash 8KB RAM
Ultra Low Power design
Li-Po battery connector for hand-held applications
UEXT connector which allows many existing modules like RF, ZIGBEE, GSM, GPS to be connected
Two LEDs
One USER BUTTON
RESET button
A Mini USB connector is used, which is common and used in most cell phones, so you do not have to buy other cables
All PIC ports available on a 0.1" connector match the ARDUINO platform and the second row with correct 0.1"step
The ICSP signals provided on a 0.1" step connector if you do not want to use Pinguino IDE and you want to program this board with PIC-KIT3.

DOCUMENTS

PIC32-PINGUINO-MX220 User's manual Revision A

HARDWARE

PIC32-PINGUINO-MX220 schematic in PDF format
PIC32-PINGUINO-MX220-REV.A schematic in Eagle format released under Creative Commons Attribution-Share Alike 3.0 United States License
PIC32-PINGUINO-MX220-REV.A board in Eagle format released under Creative Commons Attribution-Share Alike 3.0 United States License

SOFTWARE

PINGUINO IDE INSTALLATION on Windows
PINGUINO IDE Linux installation script
PIC32-PINGUINO-MX220 and SHIELD-EKG-EMG New demo code
PIC32-PINGUINO-MX220 and MOD-MP3-X demo code
Bluetooth Project with PIC32-PINGUINO-MX220 and MOD-BT (refer to the two .txt files in the main archive folder for more info)
PIC32-PINGUINO-OTG and MOD-MAG example
Call demo with MOD-GSM and PIC32-PINGUINO-MX220 for Pinguino IDE (refer to the two .txt files in the main archive folder for more info)
Send/Receive SMS demo with MOD-GSM and PIC32-PINGUINO-MX220 for Pinguino IDE for Pinguino IDE (refer to the two .txt files in the main archive folder for more info)

FAQ

I do everything just like in the examples with MOD-GSM but I receive no data. What do I do different?
You might need to cut the UEXT cable (or create your own wires) connecting the MOD-GSM with the board so that only data call signals are left, refer to MOD-GSM with DUINOMITE boards (CTS is held at a high position, which means it will not send data)

WARNING

Do not use the "programmer-to-go" button when there is no image on the OLIMEX PIC-KIT3 or MICROCHIP PIC-KIT3 because that might put your microcontroller in an irrecoverable state. We have tested the mentioned scenario and we can confirm it destroys PIC32 chips (using both our and the original Microchip PICKIT3). We don't take responsibility if you break your chip that way. For more info check the following: www.microchip.com/forums/m635420.aspx.